how to glue interior door frames to the wall

Platbands are applied shaped parts used in the design of window or door openings. Platbands are used to cover cracks when installing door or window frames. Installing platbands helps improve the aesthetic appearance of not only the door or window, but also the room itself. Platbands can be external and internal.

External trims are used to decorate door and window openings on the outside of a building. Internal platbands are used for the aesthetic design of door and window openings indoors. Most often, internal platbands are fastened with nails. However, lightweight platband structures can be fastened with liquid nails, silicone or polyurethane foam. You just need to ensure complete adherence of the platbands to the wall and door frame.

Any adhesive materials can withstand a certain load and, with a large weight of the platbands, will not be able to properly hold the platbands on the plane. When choosing one or another adhesive composition, check the weight and properties of the platbands. You can glue the platbands on liquid nails, or you can fix them on silicone or polyurethane foam.

Miter saw for trimming trims

Where to begin?

In order for the platbands to hold firmly, they must be properly adjusted and secured. To ensure proper fastening of the platbands, it is necessary to follow the technology and procedure for performing the work. Read here how to install extensions.

Sticking platbands using adhesives

Platbands are applied shaped parts used in the design of window or door openings.
Platbands are used to cover cracks when installing door or window frames. Installing platbands helps improve the aesthetic appearance of not only the door or window, but also the room itself. Platbands can be external and internal. External trims are used to decorate door and window openings on the outside of a building.

Internal platbands are used for the aesthetic design of door and window openings indoors. Most often, internal platbands are fastened with nails. However, lightweight platband structures can be fastened with liquid nails, silicone or polyurethane foam. You just need to ensure complete adherence of the platbands to the wall and door frame.

Miter saw for trimming trims

What types are there

There are various options for overlay strips. They differ in functions (to support the structure or for decoration), color palette, installation method (telescopic or overhead), shapes (rounded, flat, curly), sizes, materials (wood, metal, aluminum), texture (simple, carved elements, made according to a template). The finish is selected according to the style of the interior, the installation location and the volume of hidden elements (for example, a lot of cables and wires).

Made of wood

The wooden panel is made from soft linden, spruce, pine raw materials (budget models), from hard (expensive products) - ash, oak, Karelian pine, walnut, beech. They are suitable for any door materials, easy to install, environmentally friendly, adapt to any interior design, have a long service life (with proper care) and can be repaired in case of minor damage.

They are mainly used for interior door frames because they are not resistant to changes in room humidity and temperature. Strong changes lead to swelling or drying of the material.

If the surface is poorly processed, it may darken and lose its original shade. The cost of a wooden plank may be more than a door leaf if there are brass or copper elements. They are present only in designer products, but even without them the cost is higher than other types of cash.

From MDF

MDF paneling is almost no different from wooden types, so it often replaces its competitor. MDF panels are laminated with PVC film or covered with veneer, obtaining a good imitation of the structure of wood. MDF is safe for humans, because it is environmentally friendly. Wear-resistant, resistant to mechanical damage. But it can swell from high humidity. For example, in the bathroom. Materials laminated with PVC film are not expensive, but those covered with natural veneer are the opposite.

Made of plastic

Plastic paneling is made from a strong plastic mass that does not change under various negative conditions. They do not require special care products or frequent cleaning (once a week is enough), they do not melt and do not fade in the sun. The cost is low, so paneling is often used to complete repair work on installing door panels.

Don't miss: Types of walls during construction

The disadvantage of the material is the small palette of colors and models. Usually ready-made ones are available in white and brown, other colors are made to order. In addition, plastic trims must be secured carefully, because they cannot be repaired and are easily scratched.

Made of metal

This type is used for installing steel doors. Usually they are placed on the side of the street or corridor, then they are combined with the box. This allows you not to worry about how to install the panel, because the installation is carried out simultaneously with the box. But there are also separate metal racks, because there are interior steel and aluminum doors that require a metal design.

It has many advantages: resistance to moisture, sunlight, and mechanical stress. They can also be used forever, because they do not wear out like other types.

Important! People without experience may have difficulty sizing. To get everything straight, they hire craftsmen.

Preparing platbands for fastening

The platbands are pre-cut and marked. If necessary, one edge is trimmed at an angle of 45 degrees. Trimming trims is best done with a miter saw or miter box. The slats are tried on the box and marked.

How to glue platbands onto boxes? Platbands can be attached using adhesives only when the surface of the wall and the surface of the box lie in the same plane. If there are deviations, the platbands will not fit tightly to the surface, and gluing them is impossible. You will have to level the walls using putty.

Mounting at an angle of 45

This method is suitable for curly and rounded platbands. The procedure is as follows:

Measure the height of the vertical slats from the floor. They are placed on the floor, therefore, their joints with the baseboards will be on the side. The height of the vertical elements is measured from the floor. The planks from below are placed on the floor covering, which is why the joints of the baseboards and door frames are on the side.

Then the workpiece is cut according to the markings using a miter saw, and in its absence, using a hacksaw and a miter box. The top is cut at 45 degrees on the desired side.

Now the side trims are attached no higher than halfway, so that they bend at the top.

The upper loose parts of the platbands are folded back and the upper part is placed under them. At the joints, lines are marked at an angle of 45 degrees, then the excess part is cut off. Now you can secure the platbands in all remaining places.

We glue the platbands using liquid nails

If you want to learn how to glue platbands onto liquid nails, try to purchase platbands without bends and the correct shape. Plastic trims can be glued to liquid nails, provided that the walls are perfectly smooth. Check the flatness of the box over its entire height. The areas where you plan to glue the platbands must be cleared of wallpaper, cleaned, and primed. It is recommended to use PVA glue as a primer. After the glue has dried, apply liquid nails in dots to the platbands in 20 cm increments. The lath is applied to a pre-marked area and held for several minutes. Ideally, press with a clamp overnight. Different manufacturers of liquid nails have their own technological requirements. In problem areas, it is allowed to secure the slats with nails, which can then be covered with furniture wax. The strength of the bonded joint is largely influenced by properly selected adhesive. Among the most reliable, we can recommend liquid nails under the designation TITE BOND with red letters. You can also use Titebond glue with the Heavy Duty designation, which allows you to glue heavy parts. Moment glue does not always provide the required quality of connection.

When pressing platbands with liquid nails applied to the surface, glue may bleed through. In such cases, the adhesive should be removed immediately.

Elimination of defects

Even with experience and skills in decorative finishing of doorways, you can make annoying mistakes. The following tips will help disguise minor installation defects.

1. If the wall is uneven, the wooden frames may bend and the joints may diverge. To avoid this, during installation the joint is additionally secured with a finishing nail.

2. Significant defects in the wall around the door frame are covered with wide planks (10-12 cm).

3. To disguise nails when installing planks of unsaturated colors, it is good to use light furniture wax or sealant of the appropriate shade.

How to glue platbands using polyurethane foam

How to glue trims to doors using polyurethane foam? To be honest, it is quite difficult to obtain a high-quality connection of platbands to the wall surface using polyurethane foam. As in the first case, the main requirement is that the plane of the wall and the door frame be at the same level. Otherwise, it will not be possible to ensure a good fit of the platband to the wall. The platbands are glued in the same way as for liquid nails.

It is necessary to use clamps that will secure the platbands for a sufficiently long time for drying. To securely fasten the platbands, it is recommended to use nails, driving at least two into each platband.

Here are tips on how to remove polyurethane foam if it gets on your hands or objects.

Nuances you need to know when doing the work yourself

In order to hide the place of nailing, a special wax corrector is used in the color of the wood of the casing. If the wall near the doorway is perfectly flat, then it is better to attach the platband with “liquid nails”, in this case there will be no holes from nails. To avoid the appearance of cracks after cutting down the platbands, measurements must be taken correctly, without making mistakes, while making preliminary notes in pencil. This measurement option will allow you to minimize gaps, and, ideally, avoid them. Sometimes a situation may arise when the platbands diverge slightly at the place where they join. This can be corrected by fastening the trim strips with a small nail on top of the horizontal casing.

How to glue platbands onto acrylic sealants or silicone

It is also possible to glue the platbands using silicone; this is a simple and effective method of fastening. There are different types of sealants in different combinations. Lightweight trims can be perfectly glued to a perfectly flat wall using silicone and you don’t even need a clamp or nails.

Place the box flush with the wall. Clean the area where the glue is applied from dust and dirt. Apply a layer of deep penetration primer. Silicone is applied to the platbands in the middle in increments of 10 cm. The platbands are applied to a pre-marked area and left in place for several seconds.

Conclusions:

– to secure the platbands you can use silicone, liquid nails, polyurethane foam, all methods are good;

– for reliable fixation, it is recommended to use a combined method, glue the trim and secure it with a minimum number of nails, which are then masked with furniture wax.

Source

Some nuances when installing a decorative door element

Experienced professionals installing interior doors willingly share their secrets on the Internet. We offer a few simple tips that will greatly simplify the process of installing finishing parts and help you avoid mistakes and defects:

You should not perform fastenings in small increments of 10-15 cm. To properly secure a two-meter casing, 5 mounting points are enough.
If flaws and gaps are visible at the joints, they can be filled with sealant.
The width of a standard platband is usually 12 cm. If the overlay cannot cover the problem area with its dimensions, the products are ordered according to individual measurements.
The vertical platband should reach the floor itself, and not rest against the baseboard. If you do not follow this rule, the installation will look unaesthetic.
Plastic skirting boards have decorative plugs for proper connection with other parts, including platbands.
Sliding doors, when closed, partially cover the cash flow, so you should not purchase narrow slats; it is better to install them as wide as possible.

How to fix the trim of an interior door if it has come off the wall or jamb?

Author of the article: Alexandra Ivanova December 29, 2020

Although the door frame can be considered an auxiliary element, the entire appearance of the door largely depends on it. In fact, it has an exclusively decorative function, but if defects appear during operation, it also requires repairs. Despite its apparent simplicity, this issue deserves special attention.

Dismantling

Removal of platbands is usually required when cash is replaced. There is no need to worry about their safety, but the work is done carefully. Taking an ax with a sharp blade and a hammer in their hands, they begin to dismantle:

To remove the trim carefully, the interior door is placed in an open position. Positioned in the doorway, the tip of the ax is inserted in the upper corner between the bar and the frame.
The hammer is used to hit the butt of the ax until the blade plunges under the cash.
By pressing the handle on the ax, the bar is separated from the box. The further procedure consists of similar actions. They use an ax in a circle until the dismantling of the platbands is completed completely.

The procedure must be carried out carefully so that no dents are left on the door frame. Instead of an axe, homemade sharpened strips of durable metal or other similar devices are suitable.

Why are the platbands coming off?

One of the most common problems with platbands is their separation from the wall or frame, creating a gap, which spoils the appearance of the doors.

This defect may occur due to improper installation when installing doors, the appearance of unexpected loads during operation, or as a result of aging of the material over time, especially under extreme operating conditions.

Important ! In the design of interior doors, 2 types of platbands are used: overhead and telescopic strips. They have different designs, and therefore the reasons for the appearance of this defect also differ.

Invoices

An overlay platband is the simplest option.
It is a strip that closes the gap between the door frame and the wall in the plane of the wall. Such a casing may come off for various reasons:

Depending on the causes and size of the gap, measures are taken to replace or secure the overhead trim.

Telescopic

The telescopic platband has a more complex L-shape and is attached by connecting using a tongue-and-groove system on the door frame or directly on the door frame.
It not only masks the gap, but also closes the step that occurs when the thickness of the wall exceeds the thickness of the box along with the extension. This connection system increases the reliability of the element, but the telescopic trims are also capable of moving away with the formation of cracks. Taking into account the specific design, in addition to the specified circumstances, the cause of the defect is the incorrect insertion of the edge of the platband into the groove of the additional element or door frame. Most often, the problem occurs when cutting a groove yourself. It is important that its width matches the thickness of the edge of the step of the casing. A groove that is too wide simply will not fix the platband.

No less important is the accurate calculation of the width of the side shelf of the platband - its main strip should fit snugly against the wall. This is achieved by selecting the thickness of the extension. It is best to use a special additional element that already has a groove for the platband.

Width and shape of platbands

For interior doors, trims of various widths are available. When choosing the optimal one, you can, of course, in each specific case be guided only by your taste and personal preferences. However, it is more correct to select products for framing depending on the width of the doorway. The more spacious it is, the wider this decorative element, and vice versa.

Many people choose regular flat trims for door frames, which is mainly due to the price and their easier installation. But for the artistic decoration of the room, rounded or shaped products are still better suited, which can become an additional decoration for the door structure.

Choosing a repair method

If the platband has moved away from the door (wall), then the situation can be corrected by additional fastening without removing the element or by complete dismantling and subsequent more reliable fastening.
The first option is used when there is a small gap resulting from loosening of the fasteners. To fix it, just tighten the screws tighter or add more fasteners.

In case of a significant defect, repairs are carried out with the dismantling of the platbands. In this case, several techniques are used depending on the type of fastening. When fastening was done using nails (regular or decorative), dismantling is carried out using a knife with a strong, thin blade.

When fastening with self-tapping screws, masking of the caps causes a problem. Putty and putty can be removed using sandpaper. After removing the masking, the screw is simply unscrewed with a screwdriver or screwdriver.

A special approach is required when fastening with liquid nails (glue):

If you don’t have a hair dryer, you can use the mechanical method:

Important ! In case of significant deformation and damage to the casing, repairs involve dismantling it and replacing the element with a new strip.

Features of installing extensions

In order to install high-quality extensions, you first need to accurately calculate the dimensions of the door structure. Measurements are taken from the box to the edge of the wall, top, bottom and middle: the width of the additional parts will correspond to the maximum value.

If the platbands are telescopic, then you will need such a number of strips that their total width is the required value. The elements must be made of the material that makes up the remaining fragments of the door system and match in color.

Installation work is carried out in the following sequence:

the product is cut in accordance with measurements;
the door frame is cleaned;
the upper additional part is being installed;
polyurethane foam is blown into the gaps;
side additional elements are installed.

Self-tapping screws are used to secure the finish. Mounting holes with visible screw heads are decorated with plugs to match the additions.

How to secure the platbands?

After dismantling the casing, it is completely inspected, cleaned of previous fasteners and glue, and, if necessary, primed and puttyed. The door frame, door frame and wall in the places where they combine with the overlay strip are carefully inspected and cleaned. Next, the platband is installed and securely fastened, depending on its design.

Invoices

Overlay strips can be attached in the following ways:
If these methods are used correctly, reliable fastening of the platbands is ensured.

Telescopic

Fastening the telescopic casing differs from the above methods.
First of all, you need to clearly measure the width of the side shelf of the L-shaped strip. If it is more than necessary, then a gap will appear between the platband and the wall. If the width is insufficient, the bar will not fit into the lock groove. Thus, the length of this shelf should be the height of the step formed by the surface of the wall and the door frame with the extension, with the addition of the area included in the groove (usually 5–10 mm). Installation begins with inserting the end of the side shelf into a longitudinal groove made specifically for this purpose on the door frame or door frame. The entry should be tight. The introduction is carried out using a rubber mallet by light tapping. If the locking connection is not tight enough, then the groove is pre-treated with an adhesive composition. The entry of the plank into the gap must be the same along the entire length, otherwise a gap will appear between the wall and the plank.

It is recommended to start installing the telescopic platband with a horizontal jumper, and then install the elements on vertical posts. With a tight locking connection, additional fasteners are not required. However, for reliability, it is recommended to strengthen the fastening. To do this, the side adjacent to the box or extension is secured with nails, screws or liquid nails. MDF strips are fragile enough to make telescopic trims. If they are used, the locking joint must be coated with glue. Such strengthening must be done every time the casing is dismantled.

The door casing performs an important function - it provides an attractive appearance to the door, masking the junction of the door frame and the wall. It provides the desired aesthetics, but when it moves away from the door, a spoiling gap is formed. You can eliminate the defect by carrying out minor repairs on your own. With the right approach, you can easily restore your door's attractiveness.

Source

Video demonstration of door trim installation

To cash the door frame, the bathhouse owner can use molded products made of wood, MDF or plastic. Carpenters advise giving preference to laminated or veneered MDF products or PVC trim, which practically do not react to the effects of steam and temperature fluctuations.

Material and specifics of fastening:

Wooden trims can be installed on “liquid nails” or fastened with thin nails without heads. The caps can be cut off yourself or fastened using a construction gun that “shoots” studs without them. When using nails with heads, the fasteners are slightly “recessed”, and the locations are masked with wax correction pencils or acrylic sealants matched to the tone. The use of adhesives is acceptable, but will create problems if dismantling is necessary for cable installation or for further repairs. Liquid nails are applicable only in the case of perfectly aligned walls, otherwise there will be gaps between the platband and the wall being finished.
MDF trims are practically indistinguishable from their wooden counterparts in appearance, but their fastening is carried out according to special rules. To avoid damaging the planks, guide holes for the nails are drilled in advance. The holes are not through, the preferred diameter is 1-1.5 mm. MDF, like wood, can simply be glued.
They prefer to glue plastic trims. Their cost allows you to dismantle cash without regret or desire to reuse it. Flexible plastic moldings can be glued to walls with minor irregularities.

Choosing the cutting angle for joining

The angle is determined by the presence of a shaped relief on the front side. Home craftsmen figuring out how to install trim on doors have two options at their disposal:

Planks with a flat surface without a shaped shape can be cut at right angles. Do the same if the door is framed with platbands with a capital. The direction of joining can be either horizontal or vertical. Before installation, the saw cuts are painted or tinted with varnish.
Embossed moldings and platbands with a rounded surface are sawn at a standard angle of 45º. This is the most common scheme, requiring strict adherence to the rules and accuracy. The result of the slightest flaws will be unattractive cracks.

In order to perfectly cut the workpiece at an angle, you need to stock up on a miter box and a hand saw with fine teeth. A flawless edge will be achieved if the owner cuts on a cross-cutting machine equipped with a rotary platform.

Features of telescopic platbands

Buyers of doors produced by a number of domestic factories are given the opportunity not to use fasteners at all when installing trims with a patented telescopic design. The lucky owners of the “Volkhovets” or “Sofya” products will not need additional additions, since adjustments in case of vertical deviations and in case of a discrepancy between the size of the frame and the width of the opening are carried out by adjusting the telescopic door frame.

Their owners will learn in detail how to install doors with telescopic platbands from the manufacturer's instructions, since each of them has its own technological diagrams. A common feature for all is the presence of a protrusion-slot that is inserted into the groove existing on the box. It is recommended to strengthen connections with liquid nails.

Ways to glue components to interior doors

Author of the article: Alexandra Ivanova March 9, 2021

The set of interior doors includes not only the door leaf, but also platbands, frames, extensions and fittings to ensure functionality. The choice of components is influenced by the dimensions and location of the opening, and the number of elements is determined by the measurer or independently.

Joining the platband with the plinth

Some people think that the trim at the bottom needs to be cut because the baseboard should go there. It is not right. You need to cut the baseboard itself, otherwise it doesn’t look nice. Therefore, at the very beginning of the article, we said that platbands are installed before baseboards.

Plastic skirting boards have decorative plugs that allow you to make the joint of the skirting board with the platband neat.

A 45 degree cut is made on the wooden plinth. This allows you to equalize the thickness of the plinth with the thickness of the platband.

Thus, in this article we examined the topic of platbands for interior doors. By following our tips and recommendations, you can easily choose the methods of fastening and installing the planks yourself and implement them at home.

Rules for installing platbands

Platbands are components for finishing doorways that hide the gaps between the wall and the frame. The strips framing the opening perform a decorative function and improve the appearance of the doors.

Platbands differ:

Attaching the trim to the door frame differs in the methods of installation and joining to each other and depends on the type of product. Decorative elements are divided into overhead and telescopic with grooves for fastening.

To install platbands, 3 common methods are used:

Installing platbands on finishing nails is a durable and reliable option, while the insertion points of the fasteners are hidden with a wax pencil.

All mounting options are available for MDF planks.

Flat-shaped products are installed at an angle of 90 °, and elements made of wood and MDF are installed at an angle of 45 °. Before attaching the trim to the opening, you will need to mark the desired length and angle of the cut. The top strip with a right angle cut is often installed above the sidewalls, so its edge is well processed. When cutting, it is important to maintain the exact dimensions of the parts, for which a miter saw or hacksaw using a miter box is used. With an oblique cut, you should get an even angle so that the elements fit together without gaps.

Before installation begins, a preparatory stage will be required, including:

Decorative elements are attached to interior doors after finishing the walls in the room, but before installing the floor skirting boards.

What and how to glue the platbands?

To obtain a door surface without visible fixation, “liquid nails” are used.
The method is often used for white products, when ordinary nails are very noticeable. This option is only suitable for perfectly smooth walls. The adhesive is applied to the back surface of the casing, pressed firmly against the wall and kept in this position for about a minute.

The list of disadvantages of this method includes:

Finishing nails

Wooden and MDF trims are easier and better to fasten with nails with flat heads. Then, if necessary, they can be easily dismantled. And so that the platbands do not dismantle by themselves and hold tightly, the nail should be driven into the door frame at least 20 - 25 mm. It is better to make the distance between the nails the same. To simplify the task, you can pre-drill through holes in the lantern. At the end, so that the nails do not disturb the appearance, they can be painted over with a wax pencil.

You can also drive nails into the door frame first. Then use pliers to remove their caps. The length of the visible part of the nail without the head should not be greater than the thickness of the strip. Next, having placed the platband against the nails, a wooden beam wrapped in fabric is applied to the plank at the location of these nails, and with a few light blows of a hammer the plank is pressed onto the nail.

Glass installation procedure

Door structures with glass elements are divided into two types: with standard fastening using glazing beads and hidden fixation. For any glass installation option, you will first need to remove the damaged insert.

Sequencing:

Shards of broken glass are removed only with gloves on, paying attention to removing particles from the opening that make it difficult to install a new element.

The broken glass insert is wrapped in paper and disposed of, and the fragments are collected with a brush or vacuum cleaner.

After removing the damaged element, the glass is replaced with a new one. As an alternative to the standard insert, products made from organic, stained glass or hardened material are used.

When measuring glass parameters, it is important to take into account the gaps after fixing into the grooves, otherwise the element may be damaged due to pressure.

Sequence of work to replace the insert:

The remains of the dried silicone mixture are removed after a couple of days with a sharp knife.

Replacing glass with a hidden mount occurs differently. A wire is inserted into the door cavity and the wedges holding the insert are removed. The part is pulled upward after the glass is released.

What and how to glue glass?

To fix the glass insert on the door, various types of glue are used, but most of the compositions are difficult to find on the open market.
Available materials:

Hot-melt adhesive from a gun will not work, because it hardens quickly and becomes inelastic after drying, and when the door leaf vibrates, the glass will come off.

Fastening with self-tapping screws

Fastening platbands with finishing nails is simple and reliable.

Fastening with self-tapping screws is a standard option. It allows you to create a truly high-quality connection. You will have to work with wood, which means that self-tapping screws should be used specifically for this material. Fortunately, the modern market offers a wide variety of solutions. As for the length of the fastener, it must be at least 2 cm.

For work, it is best to use a screwdriver or drill. With their help, screwing in screws will be much easier. To ensure that the fasteners do not stick out above the casing, you must make small holes using a pre-prepared drill. It is taken with a diameter large enough so that you can easily work with the surface.

Self-tapping screws do not always look attractive, so if possible, their heads should be hidden.

Various solutions are used for this. For example, you can buy special decorative overlays without any problems. A wax pencil will do the job perfectly. It will fix the defect in a few seconds. After this, the door will look very beautiful and attractive.

Mirror installation

Before installing the mirror insert, you will need to remove the door and lay it on a flat surface.
Mark the exact location of the mirror on the door leaf. Sequence of work:

The glue hardens and fixes the glued surfaces within 24 hours. To improve adhesion to the door, place heavy objects on the mirror, evenly distributing the load.

What and how to glue the mirror?

The quality and reliability of the adhesive material plays a major role when installing a mirror on a door.
Panels that are not properly glued or screwed can become damaged and cause injury to others. To fix a mirror on an interior door, use:
Construction tape - a simple and quick fixation option that holds a small element on the surface of the door. The material is sold in every building materials or auto parts store. To attach the mirror you will need foam tape with a thickness of at least 0.8 mm.

The advantages of using it include the ability to remove a crookedly pasted mirror using a string or polystyrene tape and rehang it again.

Among the disadvantages of the method:

Silicone is the most suitable composition for gluing mirror panels. When working with the material, do not rush, it must be evenly distributed over the surface. Once the silicone hardens, it will not be possible to separate the parts. The preparatory process and installation take longer, but the service life is doubled compared to adhesive tape.

The advantages of the fixation method include:

The list of disadvantages includes:

After the silicone hardens, the mirror will have to be replaced to correct errors.

Liquid nails “for mirrors” are a reliable method of fastening, but once fixed, the accessory cannot be separated.

Using liquid nails can cause stains on the mirror due to the ammonia it contains.

Required materials and tools

To cover the door frame, you will naturally need platbands and one of the types of fasteners: nails, screws or glue. In addition, you need the following tools:

screwdriver with drill and bit - necessary when working with self-tapping screws;
hammer or pneumatic hammer for driving nails;
jigsaw or hand saw for wood;
miter box - for cutting corners with a hand saw;
roulette;
chisel;
construction square;
construction pencil;
wax pencil when attaching platbands to nails or screws.

Without these tools, it will not be possible to install platbands.

What and how to glue the film on the door?

Self-adhesive film is a polymer (PVC) material with a decorative front side and a sticky layer on the back.

Work algorithm:

The old film that has come away from the base is glued in the following ways:

The last option is to use quick-drying glue. This method is used if the first two did not help. An adhesive composition, such as “Super-moment”, is applied to the door and the inside of the film, pressed and rubbed into the door leaf.

Preparatory work

When installing platbands from the extension side, as a rule, no problems arise. But on the side of the door frame, carpenters quite often encounter a situation where the door block is either slightly recessed into the opening or protrudes outward. In this case, it is necessary to carry out work to hide these shortcomings.

The box is recessed

If the structure of the door block is recessed into the opening, and there is no way to correct the mistake by adding more, a thick platband is taken and an undercut is made in the wall under it. The work order is as follows:

the platband is attached to the box;
the line of the platband is marked on the wall;
using a grinder with a cutting wheel for concrete or brick, an incision is made into the wall along the drawn line;
use a chisel and hammer to knock out a recess for the platband - no need to be afraid to make the cut deeper or go beyond the line;
a small amount of cement mortar is made (it is better to use ready-made putty);
the knocked-out recess is lightly covered with mortar and the casing is immediately applied, as tightly as possible. Excess mortar that appears is removed first with a trowel or spatula, and then with a rag or rag;
The casing is removed, and the solution is given time to set.

To prevent the solution from sticking to the back of the plank, it is first moistened with water.

The platbands will look strange if the box is slightly recessed into the opening.

The box protrudes

If the box protrudes beyond the wall, a plane and wooden trim will help. The technology is simple: the size of the box is marked on the back side, after which a quarter is selected from the back side of the casing using a plane. You need to work slowly, constantly monitoring the process of selecting a recess for the box.

Sealant

There are various color options for silicone sealants on the market. Finishing the seams of door frames with color-matched sealant, due to its simplicity, is extremely popular and not labor-intensive. The most expensive step is going to the store and choosing the color composition. After selecting the material, the sealant is placed in the gaps and joints. This method is quick and simple, a beginner can handle it.

Choose the color carefully: once dry, it cannot be changed. Polyurethane types of silicones are difficult to remove from the surface: work very carefully. Over time, sealants tend to yellow and require replacement.

Telescopic models

The simplest is to attach telescopic trims to interior doors. It is made without nails, but can be supplemented with glue for greater strength. Installation features are directly related to their design. The fact is that the edges of the platbands, when connected, coincide with the edge of the extension or loot.

Telescopic trims are attached strictly to the groove of the box strip

In other words, one part goes inside the other. Thus, in order to install such products, you just need to saw off the excess and join the parts. The protrusion of the element fits into a recess in the door frame. Then you need to set the required distance, which is adjusted by the size of the recess.

Regardless of which installation method you choose for a particular situation, you should be careful, since one awkward movement can ruin the entire structure. If there are unevenness on the wall, it is necessary to first level them so that there are no gaps, this applies to absolutely all models of platbands, regardless of the material of manufacture and configuration.

Final part

Installing platbands cannot be called too simple, especially if the home craftsman does not have experience in this area. However, with due diligence and accuracy, anything is possible. If a home master doubts his abilities, it is better to seek help from specialists. After all, by sawing off the extra half a centimeter, you can completely ruin the platband fabric. However, it is not a fact that the store will have the desired color. If the master decides to do all the work himself, then the best option would be to first practice on unnecessary boards.

We hope that the information presented today will be useful to novice home craftsmen. The editors of our online magazine will be happy to answer your questions if any arise during the reading process. All you have to do is state them in the comments below. There you can share your method of washing down the platbands at the desired angle. If you liked the article, do not forget to rate it - your opinion is extremely important to us. And finally, as has already become customary, we bring to your attention a short video that will help to more fully reveal today’s topic. Take care of yourself, your loved ones and be healthy!