Hinged wardrobe - types and features of cabinets with hinged facades

>

When choosing furniture for a house or apartment, you should pay attention not only to the frame design, internal filling, but also to the door opening system. There are different options. Devices with sliding doors are considered more modern, but many still prefer the good old classics, which include a hinged wardrobe.

Hinged wardrobe - features and advantages

The main difference between such products and other pieces of furniture for similar purposes is the principle of movement of the doors, which open forward and to the sides. Rotation around the vertical axis is carried out using handles or a special device that is activated by light pressure.

The doors are attached with hinges to the frame or side walls.

The advantages of such furniture are:

• reasonable price;
• high level of reliability;
• ease of use;
• long service life.

For the sake of objectivity, do not forget about the disadvantages. Due to the way doors move, it is necessary to have enough free space in front of the cabinet. This, unfortunately, is not always possible. If the room has a small area or disproportionate dimensions (too narrow), then a cabinet with a hinged facade will look bulky and its use will be difficult.

How can you reduce the cost of a built-in wardrobe?

Reducing the price of a cabinet is, of course, a way of compromises, but not all of them will be painful for you. So what can you give up? If you are planning a wardrobe, replace the expensive aluminum system with a cheap steel one. It is, of course, less reliable, but if you do not look too far ahead, it will do just fine. The service life of an aluminum system is 20 years, while that of a steel system is on average 5-7. Well, the steel one is noisier. Another saving resource is the number and design of doors. If you replace narrow doors with fewer wide ones, it will be cheaper. In some places you can abandon doors altogether - make a combined façade with open shelves or install hinged doors instead of compartment doors.

You can reduce the cost of a cabinet by using the materials used. Instead of the expensive chipboard that goes on the facade, use a white or thinner board inside. It is usually significantly cheaper. If you plan the shelves correctly, their load-bearing capacity will not deteriorate. Full-extension drawers are convenient, but quite expensive. You can replace ball bearing guides with roller guides. Yes, the drawers will not slide as smoothly and they will not be able to be pulled out completely, but this is not always important. Or give up drawers in favor of regular shelves.

You can save on shelf fastenings. Instead of invisible eccentrics that pull shelves and sides together, use regular corners. In essence, there are no inconveniences from them - on the contrary: if you want, you can rearrange the shelves differently. The only case when it is impossible to refuse eccentrics is when the shelves serve as stiffening ribs that hold the cabinet structure, for example, in the outer section with an open, non-built-in side panel.

Information provided by the site mebeldok.com

Design and types of fittings for swing doors for a closet

For normal operation of the swing system, high-quality fittings are required. It is the key to long-term use of such products. The main elements are hinges, from which a high margin of safety is required. The choice depends on the size of the cabinet, the material used, and the weight of the doors.

The classification is based on the principle of placing the door on the hinge body.

• When closed, the overhead fittings are tightly pressed to the end part. The doors in this state completely hide the furniture body.
• The semi-overlay type is used when 2 facades are hung on one side stand at once. The loop has a slight bend, which ensures this arrangement.
• Inset hinges resemble the previous type, but their base bend is greater. Their task is to place the façade inside the building.
• Corner elements are necessary to secure the doors in corner cabinets.
• The inverse view allows the doors to open 180°.
• Piano hinges are considered obsolete and are almost never used due to low reliability.
• The card-type fittings are similar to the previous design. They are installed on furniture made in retro style. You can often find products of unusual shapes to enhance the decorative effect.
• Adit hinges are used for hanging sashes to false facades or “blind” walls.
• The heel mechanism is installed in the corners of the door at the bottom and top. This type is not able to withstand heavy weight, so they are used for facades made of lightweight materials.

Depending on the size and weight of the door leaf, the required number of hinges is calculated. For lengths up to 1 m, 2 pieces are sufficient. Increasing the parameter will require installing an additional part in the middle of the sash.

As for weight, starting from 9 kg, one more loop is added. It is believed that an increase in weight of 5 kg requires additional fastening. Screws are used to secure the fittings.

Facade design

When choosing a wardrobe for a room, you need to focus on the style of the room. Belonging to a specific direction of a particular product is determined by the presence of certain elements and properties:

1. The classic style is characterized by elegance in design and correct geometry. The structures are made from natural solid wood or replaced with more affordable raw materials (MDF, laminated chipboard) that imitate the texture of wood. The facade is decorated mainly in calm, pastel colors.
2. Modern style is characterized by straight lines combined with unusual decor. The facade of the product can be decorated using bright elements, decorative stickers, mirror inserts, and photo printing.
3. Cabinets in country or Provence style are made from natural raw materials; they are characterized by natural shades, practicality and simplicity. The structures are not overloaded with decor. For decoration, the aging effect and decoupage technique are often used.
4. Designs in the shabby chic style are distinguished by sophistication, originality and romance. The main features are facade wear and vintage. The furniture is usually made in pastel colors - vanilla, turquoise, lilac, azure.
5. High-tech is characterized by straight lines and the use of futuristic elements in decoration - glass, chrome, metallic inserts.
6. Baroque presupposes the presence of pompous decor, gilding, and ornate patterns.

The swing wardrobe is a beautiful, functional design. With its help, you can not only emphasize the design of the room, but also add unusual notes to the interior. A variety of models will satisfy the tastes and wishes of even the most demanding buyer.

Classical

Modern

Country

Provence

Shabby chic

High tech

Baroque

Doors for hinged wardrobes

Depending on the number of sashes, all models are divided into several types.

The most common is the double-leaf wardrobe. It is suitable for small rooms; its rectangular shape without any frills does not require much space for installation.

The most modest dimensions have a single-door design or, in other words, a pencil case.

It is advisable to install products equipped with 3 or 4 doors in spacious rooms. They can be equipped with mezzanines on top, which increases their capacity.

A five-door wardrobe is essentially a mini dressing room. To install it, you must have enough free space. Otherwise it will look too bulky.

There are standards that determine the dimensions of the doors in a swing structure.

The maximum length is 2.5–2.7 m.

A width of less than 30 cm does not add attractiveness to the product. The optimal interval is considered to be from 40 to 50 cm. The maximum value should not exceed 65 cm. Otherwise, the load on the fittings increases, which can cause distortion and destruction of the door leaf.

The design distinguishes between solid and frame facades.

The first type is a canvas made of one material. Used in production:

• natural wood;
• MDF;
• Chipboard.

Frame facades have great potential. Their design consists of a frame and a panel. A thin sheet is inserted into the frame, which is fixed in special grooves using glazing beads. They are attached with nails or glue. MDF, natural wood or aluminum are used for framing. Inserts are made from any types of materials used in furniture production.

This design option has a number of advantages:

• reduced weight;
• variety of decoration;
• efficiency;
• combination of several materials.

Which one is better to choose?

When choosing furniture, you must remember that for a small room it is better to choose a small wardrobe. For a bedroom, the best option would be a corner model. Products have one leaf, two, three or more. A single door with drawers is suitable for storing many items of clothing. It can be used either alone or in combination with other cabinets.

If the size of the room allows, you can install a large swing wardrobe with 6 doors. It will look great in a spacious bedroom or living room. The facades can be decorated with glossy plastic or in a classic style made of solid wood. Models made from chipboard with mezzanines and a mirror are an excellent option for a hallway. Small models with various drawers and shelves for storing various things and objects are well suited for a dacha.

There is an opportunity to make a cabinet with your own hands. You can choose an individual version of the cabinet, the hinged doors of which will be decorated as desired.

For a small bathroom, it is recommended to choose lighter bedding colors. The number of doors for the closet in the toilet is 1 or 2. The model of the bathroom cabinet can contain a mirror. The internal filling for a sanitary cabinet can be supplemented with all the necessary drawers, shelves for storing personal hygiene products and home care products.

Types of coating for hinged cabinet facades

There are different options for the final finishing of facades. This allows designers to find new solutions, and buyers to choose a product that best suits the rest of the interior.

• Pasting with PVC film is the most budget option. There is a wide palette of shades and textures.
• Acrylic dyes allow you to achieve unusual effects: pearlescent, glossy or matte surfaces. A protective layer of varnish is applied on top.
• Decorating with plastic does not burden the doors and makes it possible to add bright accents to the interior. High-quality material is highly durable and does not require special care.
• Veneering facades made of MDF or chipboard imitates natural wood, but has an affordable price and less weight.
• Glass is decorated using different techniques: sandblasting, fusing, matting, stained glass, colored varnish.
• Mirror surfaces can visually expand the boundaries of a room and make it brighter. They are complemented with colored inserts, carvings, etc.
• Leather, matched to the color of upholstered furniture made of the same material, will create a harmonious environment, and it is also practical.
• Unique design can be achieved using photo printing. The selection of images can satisfy any request.

Mirror, plinth and lighting

Mirror The most popular way to place a mirror in a closet is to make the doors mirrored. You can cover the closet with mirrors completely or partially. It is ergonomic: the mirror does not take up additional space, and reflective surfaces add shine, light and volume to the interior. If you are not a fan of large mirror surfaces in the interior, mirror the inner surfaces of the doors. True, this method is only suitable for swing structures. Two open doors with mirrors inside will provide the effect of a dressing table: you can see yourself both in front and behind.

Base

This element of the built-in wardrobe is useful if you have an uneven floor, which means there may be problems with doors mounted to the very bottom. Coupe doors will slide downhill, and you won’t be able to install a guide on bumps. Swinging doors can also warp, in addition, there will be unsightly gaps between the door and the floor. The plinth allows you to level the lower level of the cabinet, eliminating these problems.

Lighting Additional lighting of the closet is effective, practical, but not at all necessary. Using lighting, you can make open shelves more interesting and the space behind glass doors more mysterious. After all, illuminated shelves make it easier to find what you need. Mounting lighting inside sections makes sense if you have open shelves and want a beautiful decorative effect. Lighting hidden inside one shelf will not reach another compartment. If you want to illuminate the contents of the closet so as not to rummage through things in the dark, install lamps in the canopy. Don't forget to leave a gap between the canopy and the top border of the swing doors so they don't get caught. The transformer for built-in lamps is usually installed on the roof of the cabinet.

Designs of hinged cabinets

By design, a cabinet with hinged doors can be framed or built-in.

In the first case, the product is a free-standing piece of furniture, with all the necessary components (side and back walls, bottom, lid, facade). It can be moved around the apartment, and you don’t have to do any design work. Simply select the product of the required size and design.

Disadvantages of such a cabinet:

• occupies a large area;
• capacity is less than that of the built-in type.

In built-in furniture, some elements are replaced by walls, floors and ceilings. This approach allows you to make the most efficient use of the space of the room, especially if there are niches or recesses in it. The cost of the product is slightly lower than that of the previous type. It also has a large capacity and is able to hide the shortcomings of the room.

Weaknesses include: impossibility of rearrangement, strict requirements for site preparation, complex installation.

According to the form of execution, the following models are distinguished:

• straight;
• corner;
• radius.

Products that combine several options are considered combined.

Wardrobe size

Cabinet dimensions for one or a separate unit are depth, width, height and length. The design can be selected based on the size of the room. For small rooms, buy compact cabinets with a minimum width and depth. For shared rooms, book a multi-level gardener at full price.

Depth

The depth of the cabinet corresponds to the width of the belts. The standard depth of the rower locker below is 60 cm for the cart and 70 cm for the locker. The calculation is as follows: the width of the hook for adults is approximately 45-50 centimeters. Even a bag with light clothes takes up 50 centimeters, and with a large outer fabric it takes up 55 centimeters.

Cabinet dimensions are calculated in millimeters. The standard cabinet depth in millimeters is 550.

The 60 cm deep module is enough to accommodate clothes and accessories

Width

The profile width of the model is not standardized. The standard width of a wardrobe is 40 centimeters, it is determined by the size of the shoe boxes. The width of the payment area is not less than: 40 centimeters - the minimum required to place hooks on the shelves.

For you, determine the width as follows: look at the depth of the model and calculate how many weights there will be on the pole. With a depth of at least 55 cm and at the end of the space, a maximum of 10 blades can be placed on the boom, taking into account the free space.

Given the width of the corner cabinet, look at the dead spots and think about how to get rid of them

Height

The height of the cabinet will depend on the height of the ceilings in the room. For standard chipboard frames, the height is standardized to the height of the wooden slab - 278 centimeters or 2.8 meters. A cabinet of this height can be freely placed in an apartment room.

The high basic design of the lockers is determined by the length of the clothing: under the longest dress it should not go down to the floor. The height of the counterclock is measured from the ceiling. The best option for large rooms is a wall cabinet. In small rooms it is better to abandon the center: with it the ceiling is visually lower.

In a large, high room you can place a tall wardrobe up to the ceiling

Length

The standard length of a chipboard cabinet is 278 centimeters. But you can order the smallest or largest cabinet - when choosing the length of the module, use the dimensions of the room. The maximum length of the cabinet is up to four meters, taking into account the reference point. The minimum length of a narrow cabinet is one meter. The length of the door with guide is 50 centimeters.

If the space in the room does not allow you to place a long cabinet, change the filling of the form. Model with a slit for long dresses and two bars for blouses and tops, sleeves and a skirt at the bottom.

The principle of ergonomics in action: when there is no room for a long rod, the space is divided into two parts

Door width

The standard width of sliding doors is from 60 to 80 centimeters. The maximum for positive door structures is 120 centimeters. The longer it takes to do this, it will damage the guidance system. The optimal width of a swing door is 60 centimeters. There is no need to order wider doors - they are heavier and put pressure on the hinges.

The width of the door depends on the width of the section. When planning to fill a section, try to avoid dead spots that cannot be reached and filled. The correct door width will help get rid of such corners. If you order a wardrobe on four sides with doors divided in the middle, then the empty zones will definitely not stop.

The standard width of mirror doors is 60 centimeters - it is better not to stretch the structure, but to make more sections

How the frame of a swing wardrobe is designed - what to look for when choosing

The cabinet frame includes a number of elements:

• back panel;
• side walls:
• bottom;
• ceiling slab.

Different materials are used for their manufacture.

• Laminated chipboard has a wide selection of colors and textures, the price is affordable for a large number of buyers.
• MDF will cost a little more, but this is due to its higher characteristics.
• The most expensive option is solid wood.

It would be useful to pay attention to the thickness of the walls. Chipboard comes in 3 sizes (16,18, 25 mm). The third option is considered the most reliable. The structure of a high-quality slab should consist of 3 parts. The outer layers serve as protection from mechanical stress, and the inner layer is required to hold the fittings.

The back wall is made from fiberboard or plywood. It is attached with self-tapping screws at the end. This method is the simplest, but the least reliable. Over time, a gap may form through which dust can penetrate. The preferable option is when the panel is inserted into a groove, and the best way is to make the back wall from chipboard.

When using chipboard, it is important to have an edge on the end parts of the board. This prevents harmful substances from entering the living atmosphere. For these purposes, 2 types of films are used: PVC and melamine.

<

>

The first type is considered the best: it provides good protection against moisture and is highly durable. The film thickness is in the range from 0.4 to 2 mm. The optimal value is 1 mm. Thicker film may be too noticeable on protruding ends.

The melamine type is usually used only on invisible areas.

A simple solution accessible to everyone

To get the job done quickly, we choose one of the least labor-intensive options for making hinged cabinet doors:

• from panel;
• from finishing plywood ½ inch;
• according to your size from professionals;
• hanging store-bought sashes.

Homemade paneled doors are hung on semi-concealed overhead hinges. There is no need to cut the grooves with a milling cutter; the sashes can be made to the required size; upon completion of the work, the product is coated with furniture varnish.

Rice. 1. Plywood doors with a semi-secret hinge

Homemade swinging plywood doors have trim around the edges. Each sash should protrude about a centimeter beyond the front frame. No groove cutting is required; fastening to the back of the door and the end of the front frame is easy.

Hanging ready-made doors selected in a store on semi-concealed hinges or manufacturing doors in production according to drawings makes it possible to get the job done without turning the apartment into a carpentry shop.

Rice. 2. Door hardware samples

For accessories, if there are no self-closing hinges, you can use: A – universal lock; B – roller; C – lock, locked with a key; D – door brass bolt; E – magnetic latch. The last element is most often used on glass doors.

Finishing plywood doors

Work should begin by taking the dimensions of the doorway and selecting the number of doors to be installed. With a width of more than 60 cm, one sash is not enough. If you decide to install one panel, the height and width remain unchanged. When double doors are made, the width of the opening is divided in half and about 1.3 cm is subtracted from it on each side.

Rice. 3. Making a cabinet: taking measurements

To frame the sashes, profiles with bevels of 45° are measured and cut. These pieces are secured to the panel with 11/2-inch finishing nails. Varnish coating is carried out.

On the back side of the doors there are 2 semi-secret overhead hinges. We recommend fixing them at a distance of 5 cm from the edge of the panel (top and bottom). If the door height is more than 75 cm, you should use 1 more hinge in the center. To check the correctness of the taken dimensions, it will be convenient to temporarily stick adhesive marking tape on the front frame, above 1.3 cm from the doorway.

The door is placed on the opening, the top edge is aligned with the marking tape. The location of the hinges must be marked on the front frame with pieces of the same tape.

Basic holes are drilled into which the door is secured with screws. The loops should be in the marked place. The marking tape is removed after installing the door. Lastly, door handles and other door hardware elements are attached.

Rice. 4. Making a cabinet: placing the sash on the opening and installing it

If a folding door is made, then semi-secret hinges are attached to the front frame at the bottom, and holders and latches are installed on the sides to prevent spontaneous tilting of the sash.

Rice. 5. Making a cabinet: attaching door hardware

Internal content - storage systems and planning rules

For organizing a storage system, internal content is of great importance. It includes the following elements:

• shelves are stationary and retractable, the latter make searching easier;
• drawers and baskets of different depths;
• partitions;
• barbell (one or more);
• holders;
• trouser;
• hooks;
• shoe stands.

According to the rules, the largest drawers and compartments are located at the bottom of the cabinet, and the smallest in the middle. At the very top there is usually a shelf for things that are rarely used. The lower space is reserved for shoes, suitcases, travel bags and heavy items.

If a cabinet with a hinged facade is equipped with several rods, one of which is installed almost under the lid, then it is complemented by a pantograph.

Compartments for umbrellas and other non-standard items will be useful in organizing space.

How to plan the interior space of a closet?

Designers recommend that before planning your closet, make a list of all the things that you will store in it, and then add another 20% “for the growth of your wardrobe.” Decide what will go on the shelf or in baskets (knitwear) and what will hang (pants, jackets). And how many things do you have in each category? Decide on the price: the internal filling of the cabinet can vary greatly in cost. Therefore, limit the budget you plan to meet in advance.

Longitudinal and end rods

Clothes hanging on hangers will take up the largest compartments. For women's clothing, we plan a box with a height of 150-160 cm. If long men's coats or raincoats will hang in the closet, set a height of 175 cm. Estimate at least approximately the number of items of clothing that will hang on hangers. You can put 5 cm on each hanger - this will be the width of the compartment (and the length of the longitudinal rod).

If you have a narrow closet with end rods, allow 60 cm of the width of the compartment on each hanger. There are usually not many end hangers - 2-3 pieces. Sometimes it’s worth making separate boxes with a bar for short items: skirts, trousers, shirts and blouses. They require a smaller height - 80-100 cm, which means they save space.

If men's trousers are hung without bending, allow 120 cm in height for them.

If you require a longitudinal rod length of more than 120 cm, provide a vertical support rod in the middle. It is positioned between the upper and lower partitions and is connected to the horizontal rod with a special coupling. This is necessary so that the longitudinal rod does not bend under the weight of things. If heavy things are hanging on hangers - fur coats, coats - the length of the bar without support should not exceed 100 cm.

Another important nuance: if the wardrobe is not built into a niche, but has side walls, do not plan a compartment with a rod immediately behind the outer wall. Make better ordinary horizontal shelves there. Sliding doors, rolling back and forth, push the side wall, creating an impact load. Horizontal shelves located close to the side plate will connect it with the rest of the supporting structures of the cabinet. One barbell will not provide such a strong connection.

Bar with lift (pantograph)

A pantograph is a special device that allows you to lower and raise a barbell. Such designs are quite expensive, but are indispensable in tall cabinets when you have to use space right under the ceiling. The pantograph will lower jackets and skirts directly into your hands, and then again remove the bar with things to an unattainable height.

Shelves Built-in wardrobes are ordered not only for clothes. On open shelves you can store almost everything (except for what needs to be hung): bed linen and knitwear, books and dishes. For clothes, you can use long shelves (80-120 cm), and for heavy books and dishes, the length of the shelf should not exceed 80 cm. A convenient distance between shelves is at least 40 cm.

If you are making a shelf longer than 80 cm, provide a vertical partition underneath it as additional support. Otherwise, the shelf may bend during use. In addition, the shelves are suitable for storing neatly folded jeans, bags, jewelry boxes, and hats. So make more shelves - they will all come in handy.

Special shelves

Wide shelves are designed at the top of the closet for blankets, rugs and bed linen. In addition, it would be nice to provide compartments for sports equipment. Think about what exactly you will store there. Four pairs of roller skates? Tennis rocket? Yoga mat? It is better to measure especially large devices in advance. At this moment you understand the advantage of a chess player over a bodybuilder. In addition, at the very top there is usually a large long shelf for suitcases, bags and travel equipment. Height - 45-50 cm.

Photos of cabinets with hinged facades in the interior

>

A hinged wardrobe will be a good purchase for any room.
The ability to choose a model that suits the size, color, and design simplifies the task. If furniture manufacturers were unable to satisfy your needs, you can think about a built-in design that will take into account all the features of the room. Buy a mini tractor here

Assembly of sliding doors

You can install not only swing doors, but also sliding doors with your own hands. They save space and give furniture a more stylish, modern look. Sliding doors are an integral element of the design of both built-in and cabinet wardrobes. According to the constructive solution there are:

• hanging;
• rail

In the first case, the main load is supported by the upper guide, in the second – by the lower one. With the proper dexterity and skills, a home craftsman can install any doors in a closet with his own hands. However, if you want to make a suspended structure, you will need:

• physical assistance during installation of doors;
• applying effort to move the valves;
• complex system adjustment.

Over time, under heavy weight, the upper part of the face frame will begin to sag. There are more reliable suspension systems that provide a smooth ride. We are talking about designs with a distributed load across 8 wheels (not 2, as usual) and installation of bearings in the rollers. But this system:

• takes up an additional 150 mm of cabinet space;
• does not look aesthetically pleasing;
• costs more.

An advantage of the suspension system is its low demands on the door leaf. A door made from any rough material, screwed with larger self-tapping screws, will roll properly.

Height

The maximum height of chipboard panels is 278 cm. Therefore, the height of a corner or built-in cabinet can be a maximum of 2700 mm. Usually this length is sufficient. And if the ceilings in the apartment are not high, then a closet with side walls of 2400 mm will stand almost to the ceiling, as in the photo.

If you need higher than 278 cm, then a mezzanine with small doors is installed on the roof.

Another option is possible without the use of mezzanines. Then, for the required height, the side elements are built with a joint to the required dimensions. The maximum can be reached 4 meters, but the internal inserts will also need to be divided into parts.

Minimum and maximum height

As mentioned above, the maximum height of a chipboard panel is usually 278 centimeters. Accordingly, these parameters usually limit the maximum height of the wardrobe. As a rule, customers are limited to this height.

If you need to buy a wardrobe closet for a high ceiling, the height of which is more than 278 centimeters, then on the roof of the wardrobe closet you can make an extension (mezzanine) with additional small sliding doors with their own guides. Moreover, the height of such a cabinet can be much higher than three meters.

If you don’t want to install additional sliding doors on top, then you can make single doors to the entire required height, but at the same time, the sides of the wardrobe are still built with a joint all the way to the ceiling. The maximum height of sliding doors can reach four meters, only if the internal inserts (mirror, glass, chipboard, etc.) are divided into fragments.

Installation of furniture hinges with customer care

Some furniture manufacturers try not to think about their customers. They live by the principle: “The client comes and goes, but you always want to eat.” The rustle of banknotes has become the most desirable music for these producers, making their souls feel warm and calm.

Greedy furniture makers save where they can and where they can’t. They produce a low-quality product, which within a month begins to cause a lot of trouble for the client, bringing him to tears and despair. Furniture makers sleep peacefully and don’t flinch at night.

But in vain...

The topic of our conversation today will be: installation of furniture hinges . Don’t be alarmed, I won’t teach you how to drill holes for hinges or delve into the craftsmanship of assembling furniture. I think this should be done by specialists. But, you must admit, you have the right to know what negligent furniture manufacturers can “cheat” you on. And now you will find out about it! We will ruin the sleep of hacks and slobs! They will finally start to shudder at night and realize that:

Money is important, but the client is much more important than money!

Many of you have had to deal with a situation where the doors of an almost new cabinet or cabinet simply warp under their own weight. Moreover, this does not happen a year or two after purchasing the furniture, but literally a month and a half later. What is the reason? Why do hinges not withstand loads and sag under the weight of furniture doors?

And it’s all very simple - the manufacturer of your furniture saved a little on the quality or quantity of hinges installed. Although, more often than not, such careless furniture makers save on both. Let's figure out why this happens and how you can resist the greed of the “hammer and screwdriver workers.”

Quality of installed hinges

A greedy furniture maker, purchasing hinges at a wholesale base, takes into account one single factor - cost. Such dealers simply don’t care about the quality of the fittings. They know that this product will function normally for a while, and when everything starts to fall apart, it will be too late to change anything. So the cheapest furniture hinges are sold out, they are installed in cabinets, and then the mezzanine doors fall off and fall on the client’s head at the most inopportune moment.

Why do furniture manufacturers save on hinges? The situation on the furniture fittings market is such that a furniture maker can, instead of one high-quality, solid European hinge, buy three cheap ones, stamped from thin tin cans in the poorest Chinese neighborhoods. And with wholesale purchases, decent savings are obtained, for the sake of which some furniture manufacturers easily step over their conscience.

How to determine the quality of a furniture hinge? To an inexperienced client who has difficulty distinguishing a self-tapping screw from a bolt, slob furniture makers sell crap under the guise of an expensive exclusive. They open the cabinet doors in front of his nose and say: “Just look at how well and softly the furniture hinge works! Do you know why it glows in the dark? Yes, because this is Honduras – the leading nuclear waste processing plant!”

In fact, anyone can easily learn to understand the quality of furniture hinges. You just need to pay attention to the thickness of the metal. The thicker the metal, the better the loop.

But how do you know that this hinge has thick metal and will withstand the load? After all, you need to have a standard for comparison! I think the right decision would be to go to a wholesale center that sells furniture fittings and talk to the sellers. Let them show you cheap hinges and give you the opportunity to hold expensive, high-quality hinges in your hands.

This way you can really understand the difference between cheap crap and a good product. Well, then, write down the markings of a quality hinge and the name of the manufacturer in a notebook in order to indicate this data in the contract for the manufacture of furniture. And just let them try to install something else for you!

By the way, start expanding your horizons by reading our publication: Types of furniture hinges - this is a very educational material that talks about the most popular types of hinges among furniture makers. Well, then - forward to the wholesale base for the sale of furniture fittings!

How many furniture hinges should be installed on one door?

If you think that by choosing a manufacturer of high-quality furniture hinges you can relax, then you are mistaken. The brain of an unscrupulous furniture manufacturer is programmed to deceive the buyer. And if you can’t install a cheap sludge, then instead of three expensive hinges, you can install two. I think if it was possible to put one loop, then they would do it.

What happens when the number of installed furniture hinges decreases? That's right, they cannot withstand the weight of the doors and fail. As a result, we have the same problem: sagging cabinet doors and cabinets. You need it? Do you agree that you need more information on this issue? Well then, here you go! I designed it for you in the form of a sign like this: